 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Austin Semiconductor, Inc. 8 Meg x 16 x 4 Banks Double Data Rate SDRAM COTS, Plastic Encapsulated Microcircuit FEATURES * VDD = +2.5V 0.2V, VDDQ = +2.5V 0.2V * Bidirectional data strobe (DQS) transmitted/received with data, i.e., source-synchronous data capture (has two - one per byte) * Internal, pipelined double-data-rate (DDR) architecture; two data accesses per clock cycle * Differential clock inputs (CK and CK#) * Commands entered on each positive CK edge * DQS edge-aligned with data for READs; center-aligned with data for WRITEs * DLL to align DQ and DQS transitions with CK * Four internal banks for concurrent operation * Data mask (DM) for masking write data (has two-one per byte) * Programmable burst lengths: 2, 4, or 8 * Auto Refresh and Self Refresh Modes * Longer lead TSOP for improved reliability (OCPL) * 2.5V I/O (SSTL_2 compatible) * Concurrent auto precharge option is supported * tRAS lockout supported (tRAP = tRCD) COTS COTS PEM SDRAM AS4DDR32M16 (Top View) PIN ASSIGNMENT FIGURE 1: 66-Pin TSOP OPTIONS * Configuration 32 Meg x 16 (8 Meg x 16 x 4 banks) * Packaging Plastic 66-pin TSOPII (400 mil width, 0.65mm pin pitch) * Timing - Cycle Time 6ns @ CL = 2.5 (DDR333) (FBGA only) (Future offering) 7.5ns @ CL = 2.5 (DDR266B) 8ns @ CL = 2.5 (DDR250) * Temperature Rating Industrial Temperature (-40C to +85C) Enhanced Temperature (-40C to +105C) Military Temperature (-55C to +125C) MARKING 32M16 Configuation Refresh Count Row Addressing Bank Addressing Column Addressing 8 Meg x 16 x 4 banks 8K 8K (A0 - A12) 4 (BA0, BA1) 1K (A0 - A9) DG TABLE 1: Key Timing Parameters -6 -75 -8 SPEED GRADE -6 -75 -8 CLOCKRATE CL = 2 133 MHz 100 MHz 100 MHz CL=2.5 167 MHz 133 MHz 125 MHz DATA-OUT WINDOW 2.1 ns 2.5 ns 2.7 ns ACCESS WINDOW 0.7 ns 0.75 ns 0.8 ns DQS-DQ SKEW +0.40 ns +0.5 ns -0.6 ns NOTES: IT ET XT * CL = CAS (Read) Latency For more products and information please visit our web site at www.austinsemiconductor.com AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 1 Austin Semiconductor, Inc. GENERAL DESCRIPTION The 512Mb DDR SDRAM is a high-speed CMOS, dynamic random-access memory containing 536,870,912 bits. It is internally configured as a quad-bank DRAM. The 512Mb DDR SDRAM uses a double data rate architecture to achieve high-speed operation. The double data rate architecture is essentially a 2n-prefetch architecture with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the 512Mb DDR SDRAM effectively consists of a single 2n-bit wide, oneclock-cycle data transfer at the internal DRAM core and two corresponding n-bit wide, one-halfclock-cycle data transfers at the I/O pins. A bidirectional data strobe (DQS) is transmitted externally, along with data, for use in data capture at the receiver. DQS is a strobe transmitted by the DDR SDRAM during READs and by the memory controller during WRITEs. DQS is edge-aligned with data for READs and center-aligned with data for WRITEs. This offering has two data strobes, one for the lower byte and one for the upper byte. The 512Mb DDR SDRAM operates from a differential clock (CK and CK#); the crossing of CK going HIGH and CK# going LOW will be referred to as the positive edge of CK. Commands (address and control signals) are registered at every positive edge of CK. Input data is registered on both edges of DQS, and output data is referenced to both edges of DQS, as well as to both edges of CK. Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed. The address bits registered coincident with the READ or WRITE command are used to select the bank and the starting column location for the burst access. The DDR SDRAM provides for programmable READ or WRITE burst lengths of 2, 4, or 8 locations. An auto precharge function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst access. As with standard SDR SDRAMs, the pipelined, multibank architecture of DDR SDRAMs allows for concurrent operation, thereby providing high effective bandwidth by hiding row precharge and activation time. An auto refresh mode is provided, along with a powersaving power-down mode. All inputs are compatible with the JEDEC Standard for SSTL_2. All full drive option outputs are SSTL_2, Class II compatible. COTS COTS PEM SDRAM AS4DDR32M16 NOTE: 1. The functionality and the timing specifications discussed in this data sheet are for the DLL-enabled mode of operation. 2. Throughout the data sheet, the various figures and text refer to DQ's as "DQ." The DQ term is to be interpreted as any and all DQ collectively, unless specifically stated otherwise. Additionally, the DQ's are divided into two bytes, the lower byte and upper byte. For the lower byte (DQ0 through DQ7) DM refers to LDM and DQS refers to LDQS. For the upper byte (DQ8 through DQ15) DM refers to UDM and DQS refers to UDQS. 3. Complete functionality is described throughout the document and any page or diagram may have been simplified to convey a topic and may not be inclusive of all requirements. 4. Any specific requirement takes precedence over a general statement. FIGURE 2: 512Mb DDR SRAM Part Number EXAMPLE: AS4DDR32M16DG-75/IT AS4DDR 32M16 Package Speed / Temperature TEMPERATURE Industrial Temperature Enhanced Temperature Military Temperature SPEED -6 -75 -8 tCK = 6ns, CL = 2.5 tCK = 7.5ns, CL = 2.5 tCK = 8ns, CL = 2.5 PACKAGING 400 mil TSOP DG IT ET XT AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 2 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 3: FUNCTIONAL BLOCK DIAGRAM 32 Meg x 16 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 3 Austin Semiconductor, Inc. FUNCTIONAL DESCRIPTION The 512Mb DDR SDRAM is a high-speed CMOS, dynamic random-access memory containing 536,870,912 bits. The 512Mb DDR SDRAM is internally configured as a quad-bank DRAM. The 512Mb DDR SDRAM uses a double data rate architecture to achieve high-speed operation. The double data rate architecture is essentially a 2n-prefetch architecture, with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the 512Mb DDR SDRAM consists of a single 2n-bit wide, one-clock-cycle data transfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins. Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed (BA0, BA1 select the bank; A0-A12 select the row). The address bits registered coincident with the READ or WRITE command are used to select the starting column location for the burst access. Prior to normal operation, the DDR SDRAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command descriptions, and device operation. COTS COTS PEM SDRAM AS4DDR32M16 supply and reference voltages are stable, and the clock is stable, the DDR SDRAM requires a 200s delay prior to applying an executable command. Once the 200s delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a LOAD MODE REGISTER command should be issued for the extended mode register (BA1 LOW and BA0 HIGH) to enable the DLL, followed by another LOAD MODE REGISTER command to the mode register (BA0/ BA1 both LOW) to reset the DLL and to program the operating parameters. Two-hundred clock cycles are required between the DLL reset and any READ command. A PRECHARGE ALL command should then be applied, placing the device in the all banks idle state. Once in the idle state, two AUTO REFRESH cycles must be performed (tRFC must be satisfied.) Additionally, a LOAD MODE REGISTER command for the mode register with the reset DLL bit deactivated (i.e., to program operating parameters without resetting the DLL) is required. Following these requirements, the DDR SDRAM is ready for normal operation. REGISTER DEFINITION Mode Register The mode register is used to define the specific mode of operation of the DDR SDRAM. This definition includes the selection of a burst length, a burst type, a CAS latency and an operating mode, as shown in Figure 4 on page 5. The mode register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power (except for bit A8, which is self-clearing). Reprogramming the mode register will not alter the contents of the memory, provided it is performed correctly. The mode register must be loaded (reloaded) when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating the subsequent operation. Violating either of these requirements will result in unspecified operation. Mode register bits A0-A2 specify the burst length, A3 specifies the type of burst (sequential or interleaved), A4A6 specify the CAS latency, and A7-A12 specify the operating mode. INITIALIZATION DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in undefined operation. Power must first be applied to VDD and VDDQ simultaneously, and then to VREF (and to the system VTT). VTT must be applied after VDDQ to avoid device latch-up, which may cause permanent damage to the device. VREF can be applied any time after VDDQ but is expected to be nominally coincident with VTT. Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input but will detect an LVCMOS LOW level after VDD is applied. After CKE passes through VIH, it will transition to a SSTL 2 signal and remain as such until power is cycled. Maintaining an LVCMOS LOW level on CKE during power-up is required to ensure that the DQ and DQS outputs will be in the High-Z state, where they will remain until driven in normal operation (by a read access). After all power AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 4 Austin Semiconductor, Inc. BURST LENGTH Read and write accesses to the DDR SDRAM are burst oriented, with the burst length being programmable, as shown in Figure 4. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command.Burst lengths of 2, 4, or 8 locations are available for both the sequential and the interleaved burst types. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the burst will wrap within the block if a boundary is reached. The block is uniquely selected by A1-Ai when the burst length is set to two, by A2-Ai when the burst length is set to four and by A3-Ai when the burst length is set to eight (where Ai is the most significant column address bit for a given configuration). The remaining (least significant) address bit(s) is (are) used to select the starting location within the block. The programmed burst length applies to both READ and WRITE bursts. BURST TYPE Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the burst type and is selected via bit M3. The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column address, as shown in Table 2, Burst Definition. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 4: Mode Register Definition TABLE 2: BURST DEFINITION STARTING BURST COLUMN LENGTH ADDRESS 2 A0 0 1 A1 A0 00 01 10 11 A2 A1 A0 000 001 010 011 100 101 110 111 ORDER OF ACCESS WITHIN A BURST TYPE = TYPE = SEQUENTIAL INTERLEAVED 0-1 1-0 0-1-2-3 1-2-3-0 2-3-0-1 3-0-1-2 0-1-2-3-4-5-6-7 1-2-3-4-5-6-7-0 2-3-4-5-6-7-0-1 3-4-5-6-7-0-1-2 4-5-6-7-0-1-2-3 5-6-7-0-1-2-3-4 6-7-0-1-2-3-4-5 7-0-1-2-3-4-5-6 0-1 1-0 0-1-2-3 1-0-3-2 2-3-0-1 3-2-1-0 0-1-2-3-4-5-6-7 1-0-3-2-5-4-7-6 2-3-0-1-6-7-4-5 3-2-1-0-7-6-5-4 4-5-6-7-0-1-2-3 5-4-7-6-1-0-3-2 6-7-4-5-2-3-0-1 7-6-5-4-3-2-1-0 4 NOTES: 1. Whenever a boundary of the block is reached within a given sequence in Table 2, the following access wraps within the block. 2. For a burst length of two, A1 - Ai select the two-data-element block; A0 selects the first access within the block. 3. For a burst length of four, A2 - Ai select the four-data-element block; A0-A1 select the first access within the block. 4. For a burst length of eight, A3 - Ai select the eight-data-element block; A0-A2 select the first access within the block. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 8 AS4DDR32M16 Rev. 1.5 06/06 5 Austin Semiconductor, Inc. READ LATENCY The READ latency is the delay, in clock cycles, between the registration of a READ command and the availability of the first bit of output data. The latency can be set to 2, or 2.5 clocks, as shown in Figure 5. If a READ command is registered at clock edge n, and the latency is m clocks, the data will be available nominally coincident with clock edge n + m. Table 3, CAS Latency (CL), on page 6 indicates the operating frequencies at which each CAS latency setting can be used. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 5: CAS LATENCY OPERATING MODE The normal operating mode is selected by issuing a MODE REGISTER SET command with bits A7-A12 each set to zero, and bits A0-A6 set to the desired values. A DLL reset is initiated by issuing a MODE REGISTER SET command with bits A7 and A9-A12 each set to zero, bit A8 set to one, and bits A0-A6 set to the desired values. Although not required by the Austin Semiconductor device, JEDEC specifications recommend when a LOAD MODE REGISTER command is issued to reset the DLL, it should always be followed by a LOAD MODE REGISTER command to select normal operating mode. All other combinations of values for A7-A12 are reserved for future use and/or test modes. Test modes and reserved states should not be used, as unknown operation or incompatibility with future versions may result. TABLE 3: CAS LATENCY (CL) SPEED -6 -75 -8 ALLOWABLE OPERATING CLOCK FREQUENCY CL = 2 75 < f < 133 75 < f < 100 75 < f < 100 CL = 2.5 75 < f < 167 75 < f < 133 75 < f < 125 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 6 Austin Semiconductor, Inc. EXTENDED MODE REGISTER The extended mode register controls functions beyond those controlled by the mode register; these additional functions are DLL enable/disable, and output drive strength. These functions are controlled via the bits shown in Figure 6. The extended mode register is programmed via the LOAD MODE REGISTER command to the mode register (with BA0 = 1 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. The enabling of the DLL should always be followed by a LOAD MODE REGISTER command to the mode register (BA0/BA1 both LOW) to reset the DLL. The extended mode register must be loaded when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating any subsequent operation. Violating either of these requirements could result in unspecified operation. COTS COTS PEM SDRAM AS4DDR32M16 MODE FIGURE 6: EXTENDED REGISTER DEFINITION OUTPUT DRIVE STRENGTH The normal drive strength for all outputs are specified to be SSTL2, Class II. This device supports a programmable option for reduced drive. This option is intended for the support of the lighter load and/or point-to-point environments. The selection of the reduced drive strength will alter the DQ pins and DQS pins from SSTL2, Class II drive strength to a reduced drive strength, which is approximately 54 percent of the SSTL2, Class II drive strength. NOTES: 1. E14 and E13 (BA1 and BA0) must be "0, 1" to select the Extended Mode Register vs. the base Mode Register. 2. The reduced drive strength option is supported. 3. The QFC# option is not supported. DLL ENABLE/DISABLE When the part is running without the DLL enabled, device functionality may be altered. The DLL must be enabled for normal operation. DLL enable is required during power-up initialization and upon returning to normal operation after having disabled the DLL for the purpose of debug or evaluation. (When the device exits self refresh mode, the DLL is enabled automatically.) Any time the DLL is enabled, 200 clock cycles must occur before a READ command can be issued. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 7 Austin Semiconductor, Inc. COMMANDS Table 4 and Table 5 provide a quick reference of available commands. This is followed by a verbal description of each command. Two additional Truth Tables, Table 7 and Table8 appear following the Operation section, provide current state/ next state information. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 4: TRUTH TABLE - COMMANDS (Note 1 applies to all commands) FUNCTION DESELECT (NOP) NO OPERATION (NOP) ACTIVE (Select bank and activate row) READ (Select bank and column, and start READ burst) WRITE (Select bank and column, and start WRITE burst) BURST TERMINATE PRECHARGE (Deactivate row in bank or banks) AUTO REFRESH or SELF REFRESH (Enter self refresh mode) LOAD MODE REGISTER CS# H L L L L L L L L RAS# X H L H H H L L L CAS# X H H L L H H L L WE# X H H H L L L H L ADDR NOTES X 9 X 9 Bank/Row 3 Bank/Col 4 Bank/Col 4 X 8 Code 5 X 6, 7 Op-Code 2 NOTES: 1. CKE is HIGH for all commands shown except SELF REFRESH. 2. BA0-BA1 select either the mode register or the extended mode register (BA0 = 0, BA1 = 0 select the mode register; BA0 = 1, BA1 = 0 select extended mode register; other combinations of BA0-BA1 are reserved). A0-A12 provide the opcode to be written to the selected mode register. 3. BA0-BA1 provide bank address and A0-A12 provide row address. 4. BA0-BA1 provide bank address; A0-A9 provide column address. A10 HIGH enables the auto precharge feature (non persistent), and A10 LOW disables the auto precharge feature. 5. A10 LOW: BA0-BA1 determine which bank is precharged. A10 HIGH: all banks are precharged and BA0-BA1 are "Don't Care." 6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW. 7. Internal refresh counter controls row addressing; for within the Self Refresh mode all inputs and I/Os are "Don't Care" except for CKE. 8. Applies only to read bursts with auto precharge disabled; this command is undefined (and should not be used) for read bursts with auto precharge enabled and for write bursts. 9. DESELECT and NOP are functionally interchangeable. TABLE 5: TRUTH TABLE - DM OPERATION (Note 1 applies to all commands) FUNCTION Write Enable Write Inhibit DM L H DQ Valid X NOTE: 1. Used to mask write data; provided coincident with the corresponding data. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 8 Austin Semiconductor, Inc. DESELECT The DESELECT function (CS# HIGH) prevents new commands from being executed by the DDR SDRAM. The DDR SDRAM is effectively deselected. Operations already in progress are not affected. COTS COTS PEM SDRAM AS4DDR32M16 NO OPERATION (NOP) The NO OPERATION (NOP) command is used to instruct the selected DDR SDRAM to perform a NOP (CS# is LOW with RAS#, CAS#, and WE# are HIGH). This prevents unwanted commands from being registered during idle or wait states. Operations already in progress are not affected. row will remain open for subsequent accesses. Input data appearing on the DQ is written to the memory array subject to the DM input logic level appearing coincident with the data. If a given DM signal is registered LOW, the corresponding data will be written to memory; if the DM signal is registered HIGH, the corresponding data inputs will be ignored, and a WRITE will not be executed to that byte/column location. PRECHARGE The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access a specified time (tRP) after the precharge command is issued. Except in the case of concurrent auto precharge, where a READ or WRITE command to a different bank is allowed as long as it does not interrupt the data transfer in the current bank and does not violate any other timing parameters. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command will be treated as a NOP if there is no open row in that bank (idle state), or if the previously open row is already in the process of precharging. LOAD MODE REGISTER The mode registers are loaded via inputs A0-A12. See mode register descriptions in the Register Definition section. The LOAD MODE REGISTER command can only be issued when all banks are idle, and a subsequent executable command cannot be issued until tMRD is met. ACTIVE The ACTIVE command is used to open (or activate) a row in a particular bank for a subsequent access. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-A12 selects the row. This row remains active (or open) for accesses until a precharge command is issued to that bank. A precharge command must be issued before opening a different row in the same bank. AUTO PRECHARGE Auto precharge is a feature which performs the same individual-bank precharge function described above, but without requiring an explicit command. This is accomplished by using A10 to enable auto precharge in conjunction with a specific READ or WRITE command. A precharge of the bank/ row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. Auto precharge is nonpersistent in that it is either enabled or disabled for each individual Read or Write command. This device supports concurrent auto precharge if the command to the other bank does not interrupt the data transfer to the current bank. Auto precharge ensures that the precharge is initiated at the earliest valid stage within a burst. This "earliest valid stage" is determined as if an explicit PRECHARGE command was issued at the earliest possible time, without violating tRAS (MIN), as described for each burst type in the Operation section of this data sheet. The user must not issue another command to the same bank until the precharge time (tRP) is completed. READ The READ command is used to initiate a burst read access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-A9 selects the starting column location. The value on input A10 determines whether or not auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at the end of the READ burst; if auto precharge is not selected, the row will remain open for subsequent accesses. WRITE The WRITE command is used to initiate a burst write access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-A9 selects the starting column location. The value on input A10 determines whether or not auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at the end of the WRITE burst; if auto precharge is not selected, the AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 9 Austin Semiconductor, Inc. BURST TERMINATE The BURST TERMINATE command is used to truncate read bursts (with auto precharge disabled). The most recently registered READ command prior to the BURST TERMINATE command will be truncated, as shown in the Operation section of this data sheet. The open page which the READ burst was terminated from remains open. COTS COTS PEM SDRAM AS4DDR32M16 AUTO REFRESH AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS#-BEFORE RAS# (CBR) refresh in FPM/EDO DRAMs. This command is nonpersistent, so it must be issued each time a refresh is required. All banks must be idle before an AUTO REFRESH command is issued. The addressing is generated by the internal refresh controller. This makes the address bits a "Don't Care" during an AUTO REFRESH command. The 512Mb DDR SDRAM requires AUTO REFRESH cycles at an average interval of 7.8125s (maximum). To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM, meaning that the maximum absolute interval between any AUTO REFRESH command and the next AUTO REFRESH command is 9 x 7.8125s (70.3s). Note the JEDEC specifications only allows 8 x 7.8125s, thus the Austin Semiconductor specification exceeds the JEDEC requirement by one clock. This maximum absolute interval is to allow future support for DLL updates internal to the DDR SDRAM to be restricted to AUTO REFRESH cycles, without allowing excessive drift in tAC between updates. Although not a JEDEC requirement, to provide for future functionality features, CKE must be active (High) during the AUTO REFRESH period. The AUTO REFRESH period begins when the AUTO REFRESH command is registered and ends tRFC later. REFRESH. The procedure for exiting self refresh requires a sequence of commands. First, CK and CK# must be stable prior to CKE going back HIGH. Once CKE is HIGH, the DDR SDRAM must have NOP commands issued for tXSNR because time is required for the completion of any internal refresh in progress. A simple algorithm for meeting both refresh and DLL requirements is to apply NOPs for tXSNR time, then a DLL Reset and NOPs for 200 additional clock cycles before applying any other command. BANK/ROW ACTIVATION Before any READ or WRITE commands can be issued to a bank within the DDR SDRAM, a row in that bank must be "opened." This is accomplished via the ACTIVE command, which selects both the bank and the row to be activated, as shown in Figure 7. After a row is opened with an ACTIVE command, a READ or WRITE command may be issued to that row, subject to the tRCD specification. tRCD (MIN) should be divided by the clock period and rounded up to the next whole number to determine the earliest clock edge after the ACTIVE command on which a READ or WRITE command can be entered. For example, a tRCD specification of 20ns with a 133 MHz clock (7.5ns period) results in 2.7 clocks rounded to 3. This is reflected in Figure 8, which covers any case where 2 A subsequent ACTIVE command to another bank can be issued while the first bank is being accessed, which results in a reduction of total row-access overhead. The minimum time interval between successive ACTIVE commands to different banks is defined by tRRD. SELF REFRESH The SELF REFRESH command can be used to retain data in the DDR SDRAM, even if the rest of the system is powered down. When in the self refresh mode, the DDR SDRAM retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command except CKE is disabled (LOW). The DLL is automatically disabled upon entering SELF REFRESH and is automatically enabled upon exiting SELF REFRESH (A DLL reset and 200 clock cycles must then occur before a READ command can be issued). Input signals except CKE are "Don't Care" during SELF REFRESH. VREF voltage is also required for the full duration of SELF AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 10 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 7: ACTIVATING A SPECIFIC ROW IN A SPECIFIC BANK FIGURE 8: EXAMPLE: MEETING tRCD (tRRD) MIN WHEN 2 < tRCD (tRRD) MIN/tCK < 3 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 11 Austin Semiconductor, Inc. READs READ bursts are initiated with a READ command, as shown in Figure 9. The starting column and bank addresses are provided with the READ command and auto precharge is either enabled or disabled for that burst access. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst. NOTE: For the READ commands used in the following illustrations, auto precharge is disabled. During READ bursts, the valid data-out element from the starting column address will be available following the CAS latency after the READ command. Each subsequent data-out element will be valid nominally at the next positive or negative clock edge (i.e., at the next crossing of CK and CK#). Figure 10 shows general timing for each possible CAS latency setting. DQS is driven by the DDR SDRAM along with output data. The initial LOW state on DQS is known as the read preamble; the LOW state coincident with the last data-out element is known as the read postamble. Upon completion of a burst, assuming no other commands have been initiated, the DQs will go High-Z. A detailed explanation of tDQSQ (valid data-out skew), tQH (data-out window hold), the valid data window are depicted in Figure 37. A detailed explanation of tDQSCK (DQS transition skew to CK) and tAC (data-out transition skew to CK) is depicted in Figure 38. Data from any READ burst may be concatenated with or truncated with data from a subsequent READ command. In either case, a continuous flow of data can be maintained. The first data element from the new burst follows either the last element of a completed burst or the last desired data element of a longer burst which is being truncated. The new READ COTS COTS PEM SDRAM AS4DDR32M16 command should be issued x cycles after the first READ command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). This is shown in Figure 11. A READ command can be initiated on any clock cycle following a previous READ command. Nonconsecutive read data is shown for illustration in Figure 12. Full-speed random read accesses within a page (or pages) can be performed as shown in Figure 13. Data from any READ burst may be truncated with a BURST TERMINATE command, as shown in Figure 14. The BURST TERMINATE latency is equal to the read (CAS) latency, i.e., the BURST TERMINATE command should be issued x cycles after the READ command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). Data from any READ burst must be completed or truncated before a subsequent WRITE command can be issued. If truncation is necessary, the BURST TERMINATE command must be used, as shown in Figure 15. The tDQSS (NOM) case is shown; the tDQSS (MAX) case has a longer bus idle time. (tDQSS [MIN] and tDQSS [MAX] are defined in the section on WRITEs.) A READ burst may be followed by, or truncated with, a PRECHARGE command to the same bank provided that auto precharge was not activated. The PRECHARGE command should be issued x cycles after the READ command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). This is shown in Figure 16. Following the PRECHARGE command, a subsequent command to the same bank cannot be issued until both tRAS and tRP has been met. Note that part of the row precharge time is hidden during the access of the last data elements. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 12 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 9: READ COMMAND AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 13 Austin Semiconductor, Inc. FIGURE 10: READ BURST COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. DO n = data-out from column n. 2. Burst length = 4. 3. Three subsequent elements of data-out appear in the programmed order following DO n. 4. Shown with nominal tAC, tDQSCK, and tDQSQ. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 14 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 11: CONSECUTIVE READ BURSTS NOTES: 1. 2. 3. 4. 5. 6. DO n (or b) = data-out from column n (or column b). Burst length = 4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first). Three subsequent elements of data-out appear in the programmed order following DO n. Three (or seven) subsequent elements of data-out appear in the programmed order following DO b. Shown with nominal tAC, tDQSCK, and tDQSQ. Example applies only when READ commands are issued to same device. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. AS4DDR32M16 Rev. 1.5 06/06 15 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 12: NONCONSECUTIVE READ BURSTS NOTES: 1. 2. 3. 4. 5. DO n (or b) = data-out from column n (or column b). Burst length = 4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first). Three subsequent elements of data-out appear in the programmed order following DO n. Three (or seven) subsequent elements of data-out appear in the programmed order following DO b. Shown with nominal tAC, tDQSCK, and tDQSQ. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 16 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 13: RANDOM READ ACCESSES NOTES: 1. 2. 3. 4. 5. DO n (or x or b or g) = data-out from column n (or column x or column b or column g). Burst length = 2, 4 or 8 (if 4 or 8, the following burst interrupts the previous). n' or x' or b' or g' indicates the next data-out following DO n or DO x or DO b or DO g, respectively. READs are to an active row in any bank. Shown with nominal tAC, tDQSCK, and tDQSQ. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 17 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 14: TERMINATING A READ BURST NOTES: 1. 2. 3. 4. 5. DO n = data-out from column n. Burst length = 4. Subsequent element of data-out appears in the programmed order following DO n. Shown with nominal tAC, tDQSCK, and tDQSQ. BST = BURST TERMINATE command, page remains open. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 18 Austin Semiconductor, Inc. FIGURE 15: READ TO WRITE COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. 2. 3. 4. 5. 6. 7. DO n = data-out from column n. DI b = data-in from column b. Burst length = 4 in the cases shown (applies for bursts of 8 as well; if the burst length is 2, the BST command shown can be NOP). One subsequent element of data-out appears in the programmed order following DO n. Data-in elements are applied following DI b in the programmed order. Shown with nominal tAC, tDQSCK, and tDQSQ. BST = BURST TERMINATE command, page remains open. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. AS4DDR32M16 Rev. 1.5 06/06 19 Austin Semiconductor, Inc. FIGURE 16: READ TO PRECHARGE COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. DO n = data-out from column n. 2. Burst length = 4, or an interrupted burst of 8. 3. Three subsequent elements of data-out appear in the programmed order following DO n. 4. Shown with nominal tAC, tDQSCK, and tDQSQ. 5. READ to PRECHARGE equals two clocks, which allows two data pairs of data-out. 6. A READ command with AUTO-PRECHARGE enabled, provided tRAS(min) is met, would cause a precharge to be performed at x number of clock cycles after the READ command, where x = BL / 2. 7. PRE = PRECHARGE command; ACT = ACTIVE command. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 20 Austin Semiconductor, Inc. WRITEs WRITE bursts are initiated with a WRITE command, as shown in Figure 17. The starting column and bank addresses are provided with the WRITE command, and auto precharge is either enabled or disabled for that access. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst and after the tWR time. NOTE: For the WRITE commands used in the following illustrations, auto precharge is disabled. During WRITE bursts, the first valid data-in element will be registered on the first rising edge of DQS following the WRITE command, and subsequent data elements will be registered on successive edges of DQS. The LOW state on DQS between the WRITE command and the first rising edge is known as the write preamble; the LOW state on DQS following the last data-in element is known as the write postamble. The time between the WRITE command and the first corresponding rising edge of DQS (tDQSS) is specified with a relatively wide range (from 75 percent to 125 percent of one clock cycle). All of the WRITE diagrams show the nominal case, and where the two extreme cases (i.e., tDQSS [MIN] and tDQSS [MAX]) might not be intuitive, they have also been included. Figure 18 shows the nominal case and the extremes of tDQSS for a burst of 4. Upon completion of a burst, assuming no other commands have been initiated, the DQ will remain High-Z and any additional input data will be ignored. Data for any WRITE burst may be concatenated with or truncated with a subsequent WRITE command. In either case, a continuous flow of input data can be maintained. The new WRITE command can be issued on any positive edge of clock following the previous WRITE command. The first data element from the new burst is applied after either the last element of a completed burst or the last desired data element of a longer burst which is being truncated. The new WRITE command should be issued x cycles after the first WRITE command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). Figure 19 shows concatenated bursts of 4. An example of nonconsecutive WRITEs is shown in Figure 20. Full-speed random write accesses within a page or pages can be performed as shown in Figure 21. Data for any WRITE burst may be followed by a subsequent READ command. To follow a WRITE without truncating the WRITE burst, tWTR should be met as shown in Figure 22. Data for any WRITE burst may be truncated by a subsequent READ command, as shown in Figure 23. Note that only the data-in pairs that are registered prior to the tWTR period are written to the internal array, and any subsequent data-in should be masked with DM as shown in Figure 24. AS4DDR32M16 Rev. 1.5 06/06 COTS COTS PEM SDRAM AS4DDR32M16 Data for any WRITE burst may be followed by a subsequent PRECHARGE command. To follow a WRITE without truncating the WRITE burst, tWR should be met as shown in Figure 25. Data for any WRITE burst may be truncated by a subsequent PRECHARGE command, as shown in Figure 26 and Figure 27. Note that only the data-in pairs that are registered prior to the tWR period are written to the internal array, and any subsequent data-in should be masked with DM as shown in Figures 26 and 27. After the PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met. FIGURE 17: WRITE COMMAND Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 21 Austin Semiconductor, Inc. FIGURE 18: WRITE BURST COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. 2. 3. 4. DI b = data-in for column b. Three subsequent elements of data-in are applied in the programmed order following DI b. An uninterrupted burst of 4 is shown. A10 is LOW with the WRITE command (auto precharge is disabled). AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 22 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 19: CONSECUTIVE WRITE TO WRITE NOTES: 1. 2. 3. 4. 5. DI b, etc. = data-in for column b, etc. Three subsequent elements of data-in are applied in the programmed order following DI b. Three subsequent elements of data-in are applied in the programmed order following DI n. An uninterrupted burst of 4 is shown. Each WRITE command may be to any bank. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 23 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 20: NONCONSECUTIVE WRITE TO WRITE NOTES: 1. 2. 3. 4. 5. DI b, etc. = data-in for column b, etc. Three subsequent elements of data-in are applied in the programmed order following DI b. Three subsequent elements of data-in are applied in the programmed order following DI n. An uninterrupted burst of 4 is shown. Each WRITE command may be to any bank. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 24 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 21: RANDOM WRITE CYCLES NOTES: 1. 2. 3. 4. DI b, etc. = data-in for column b, etc. b', etc. = the next data-in following DI b, etc., according to the programmed burst order. Programmed burst length = 2, 4, or 8 in cases shown. Each WRITE command may be to any bank. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 25 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 22: WRITE TO READ - UNINTERRUPTING NOTES: 1. DI b = data-in for column b, DO n = data-out for column n. 2. Three subsequent elements of data-in are applied in the programmed order following DI b. 3. An uninterrupted burst of 4 is shown. 4. tWTR is referenced from the first positive CK edge after the last data-in pair. 5. The READ and WRITE commands are to same device. However, the READ and WRITE commands may be to different devices, in which case tWTR is not required and the READ command could be applied earlier. 6. A10 is LOW with the WRITE command (auto precharge is disabled). AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 26 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 23: WRITE TO READ - INTERRUPTING NOTES: 1. 2. 3. 4. 5. 6. 7. DI b = data-in for column b, DO n = data-out for column n. An interrupted burst of 4 is shown; two data elements are written. One subsequent element of data-in is applied in the programmed order following DI b. tWTR is referenced from the first positive CK edge after the last data-in pair. A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T2 and T2n (nominal case) to register DM. If the burst of 8 was used, DM and DQS would be required at T3 and T3n because the READ command would not mask these two data elements. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 27 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 24: WRITE TO READ - ODD NUMBER OF DATA, INTERRUPTING NOTES: 1. 2. 3. 4. 5. 6. DI b = data-in for column b, DO n = data-out for column n. An interrupted burst of 4 is shown; one data element is written. tWTR is referenced from the first positive CK edge after the last desired data-in pair (not the last two data elements). A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T1n, T2, and T2n (nominal case) to register DM. If the burst of 8 was used, DM and DQS would be required at T3 - T3n because the READ command would not mask these data elements. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 28 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 25: WRITE TO PRECHARGE - UNINTERRUPTING NOTES: 1. DI b = data-in for column b. 2. Three subsequent elements of data-in are applied in the programmed order following DI b. 3. An uninterrupted burst of 4 is shown. 4. tWR is referenced from the first positive CK edge after the last data-in pair. 5. The PRECHARGE and WRITE commands are to the same device. However, the PRECHARGE and WRITE commands may be to different devices, in which case tWR is not required and the PRECHARGE command could be applied earlier. 6. A10 is LOW with the WRITE command (auto precharge is disabled). 7. PRE = PRECHARGE command. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 29 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 26: WRITE TO PRECHARGE - INTERRUPTING NOTES: 1. 2. 3. 4. 5. 6. 7. 8. DI b = data-in for column b. Subsequent element of data-in is applied in the programmed order following DI b. An interrupted burst of 8 is shown; two data elements are written. tWR is referenced from the first positive CK edge after the last data-in pair. A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T4 and T4n (nominal case) to register DM. If the burst of 4 was used, DQS and DM would not be required at T3, T3n, T4 and T4n. PRE = PRECHARGE command. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 30 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 27: WRITE TO PRECHARGE ODD NUMBER OF DATA, INTERRUPTING NOTES: 1. 2. 3. 4. 5. 6. 7. DI b = data-in for column b. An interrupted burst of 8 is shown; one data element is written. tWR is referenced from the first positive CK edge after the last data-in pair. A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T4 and T4n (nominal case) to register DM. If the burst of 4 was used, DQS and DM would not be required at T3, T3n, T4 and T4n. PRE = PRECHARGE command. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 31 Austin Semiconductor, Inc. PRECHARGE The PRECHARGE command as shown in Figure 28, is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access some specified time (tRP) after the PRECHARGE command is issued. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. When all banks are to be precharged, inputs BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. COTS COTS PEM SDRAM AS4DDR32M16 Power-down (CKE Not Active) Unlike SDR SDRAMs, DDR SDRAMs require CKE to be active at all times an access is in progress, from the issuing of a READ or WRITE command until completion of the access. Thus a clock suspend is not supported. For READs, an access completion is defined when the Read Postamble is satisfied; for WRITEs, an access completion is defined when the Write Recovery time (tWR) is satisfied. Power-down as shown in Figure 29, is entered when CKE is registered LOW and all Table 6 criteria are met. If power-down occurs when all banks are idle, this mode is referred to as precharge power-down; if power-down occurs when there is a row active in any bank, this mode is referred to as active powerdown. Entering power-down deactivates the input and output buffers, excluding CK, CK#, and CKE. For maximum power savings, the DLL is frozen during precharge power-down mode. Exiting powerdown requires the device to be at the same voltage and frequency as when it entered power-down. However, power-down duration is limited by the refresh requirements of the device (tREFC). While in power-down, CKE LOW and a stable clock signal must be maintained at the inputs of the DDR SDRAM, while all other input signals are "Don't Care." The power-down state is synchronously exited when CKE is registered HIGH (in conjunction with a NOP or DESELECT command). A valid executable command may be applied one clock cycle later. FIGURE 28: PRECHARGE COMMAND AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 32 Austin Semiconductor, Inc. FIGURE 29: POWER-DOWN COTS COTS PEM SDRAM AS4DDR32M16 TABLE 6: TRUTH TABLE - CKE1-6 CKEn-1 L L H H NOTES: 1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge. 2. Current state is the state of the DDR SDRAM immediately prior to clock edge n. 3. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of COMMANDn. 4. All states and sequences not shown are illegal or reserved. 5. CKE must not drop low during a column access. For a READ, this means CKE must stay high until after the Read Postamble time; for a WRITE, CKE must stay high until the WRITE Recovery Time (tWR) has been met. 6. Once initialized, including during self refresh mode, VREF must be powered within the specified range. 7. Upon exit of the Self Refresh mode the DLL is automatically enabled, but a DLL Reset must still occur. A minimum of 200 clock cycles is needed before applying a READ command for the DLL to lock. DESELECT or NOP commands should be issued on any clock edges occurring during the tXSNR period. CKEn L H L H CURRENT STATE Power-Down Self Refresh Power-Down Self Refresh All Banks Idle Bank(s) Active All Banks Idle COMMANDn X X DESELECT or NOP DESELECT or NOP DESELECT or NOP DESELECT or NOP AUTO REFRESH See Table 7 ACTIONn Maintain Power-Down Maintain Self Refresh Exit Power-Down Exit Self Refresh Precharge Power-Down Entry Active Power-Down Entry Self Refresh Entry NOTES 7 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 33 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 7: TRUTH TABLE - CURRENT STATE BANK n - COMMAND TO BANK n 1-6 CURRENT STATE Any CS# H L L L L L L L L L L L L L L RAS# X H L L L H H L H H L H H H L CAS# X H H L L L L H L L H H L L H WE# X H H H L H L L H L L L H L L COMMAND/ACTION DESELECT (NOP/continue previous operation) NO OPERATION (NOP/continue previous operation) ACTIVE (select and activate row) AUTO REFRESH LOAD MODE REGISTER READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) READ (select column and start new READ burst) WRITE (select column and start WRITE burst) PRECHARGE (truncate READ burst, start PRECHARGE) BURST TERMINATE READ (select column and start READ burst) WRITE (select column and start new WRITE burst) PRECHARGE (truncate WRITE burst, start PRECHARGE) NOTES Idle Row Active Read (AutoPrecharge Disabled) Write (AutoPrecharge 7 7 10 10 8 10 10, 12 8 9 10, 11 10 8, 11 NOTES: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table 7 on page 41) and after tXSNR has been met (if the previous state was self refresh). 2. This table is bank-specific, except where noted (i.e., the current state is for a specific bank and the commands shown are those allowed to be issued to that bank when in that state). Exceptions are covered in the notes below. 3. Current state definitions: Idle:The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. 4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP commands, or allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands to the other bank are determined by its current state and Table 7, Truth Table - Current State Bank n - Command to Bank n and according to Table 8, Truth Table - Current State Bank n - Command to Bank m. Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank will be in the idle state. Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank will be in the "row active" state. Read w/Auto-Precharge Enabled: Starts with registration of a READ command with auto precharge enabled and ends when tRP has been met. Once tRP is met, the bank will be in the idle state. Write w/Auto-Precharge Enabled: Starts with registration of a WRITE command with auto precharge enabled and ends when tRP has been met. Once tRP is met, the bank will be in the idle state. 5. The following states must not be interrupted by any executable command; COMMAND INHIBIT or NOP commands must be applied on each positive clock edge during these states. Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRFC is met. Once tRFC is met, the DDR SDRAM will be in the all banks idle state. Accessing Mode Register: Starts with registration of a LOAD MODE REGISTER command and ends when tMRD has been met. Once tMRD is met, the DDR SDRAM will be in the all banks idle state. Precharging All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met, all banks will be in the idle state. 6. All states and sequences not shown are illegal or reserved. 7. Not bank-specific; requires that all banks are idle, and bursts are not in progress. 8. May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for precharging. 9. Not bank-specific; BURST TERMINATE affects the most recent READ burst, regardless of bank. 10. READs or WRITEs listed in the Command/Action column include Reads or Writes with auto precharge enabled and READs or WRITEs with auto precharge disabled. 11. Requires appropriate DM masking. 12. A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be used to end the READ burst prior to asserting a WRITE command. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 34 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 8: TRUTH TABLE - CURRENT STATE BANK n - COMMAND TO BANK m 1-6 CURRENT STATE Any Idle Row Activating, Active, or Precharging Read (AutoPrecharge Disabled) Write (AutoPrecharge Disabled) Read (With AutoPrecharge) Write (With AutoPrecharge) CS# H L X L L L L L L L L L L L L L L L L L L L L RAS# X H X L H H L L H H L L H H L L H H L L H H L CAS# X H X H L L H H L L H H L L H H L L H H L L H WE# X H X H H L L H H L L H H L L H H L L H H L L COMMAND/ACTION DESELECT (NOP/continue previous operation) NO OPERATION (NOP/continue previous operation) Any Command Otherwise Allowed to Bank m ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE ACTIVE (select and activate row) READ (select column and start new READ burst) WRITE (select column and start WRITE burst) PRECHARGE ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start new WRITE burst) PRECHARGE ACTIVE (select and activate row) READ (select column and start new READ burst) WRITE (select column and start WRITE burst) PRECHARGE ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start new WRITE burst) PRECHARGE NOTES 7 7 7 7, 9 7, 8 7 7, 3a 7, 9, 3a 7, 3a 7, 3a NOTES: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSNR has been met (if the previous state was self refresh). 2. This table describes alternate bank operation, except where noted (i.e., the current state is for bank n and the commands shown are those allowed to be issued to bank m, assuming that bank m is in such a state that the given command is allowable). Exceptions are covered in the notes below. 3. Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. Write:A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated Read with Auto Precharge Enabled: See following text - 3a Write with Auto Precharge Enabled: See following text - 3a a. The read with auto precharge enabled or write with auto precharge enabled states can each be broken into two parts: the access period and the precharge period. For read with auto precharge, the precharge period is defined as if the same burst was executed with auto precharge disabled and then followed with the earliest possible PRECHARGE command that still accesses all of the data in the burst. For write with auto precharge, the precharge period begins when tWR ends, with tWR measured as if auto precharge was disabled. The access period starts with registration of the command and ends where the precharge period (or tRP) begins.This device supports concurrent auto precharge such that when a read with auto precharge is enabled or a write with auto precharge is enabled any command to other banks is allowed, as long as that command does not interrupt the read or write data transfer already in process. In either case, all other related limitations apply (e.g., contention between read data and write data must be avoided). b. The minimum delay from a read or write command with auto precharge enabled, to a command to a different bank is summarized on the following page. (CONTINUED) AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 35 Austin Semiconductor, Inc. NOTES (Continued): FROM COMMAND TO COMMAND READ or READ w/ AP WRITE w/ AP WRITE or WRITE w/ AP PRECHARGE ACTIVE READ or READ w/ AP READ w/ AP WRITE or WRITE w/ AP PRECHARGE ACTIVE NOTES: CLRU = CAS Latency (CL) rounded up to the next integer BL = Bust Length COTS COTS PEM SDRAM AS4DDR32M16 MINIMUM DELAY (WITH CONCURRENT AUTO PRECHARGE) [1 + (BL/2)] * tCK + tWTR (BL/2) * tCK 1 tCK 1 tCK (BL/2) * tCK [CLRU + (BL/2)] * tCK 1 tCK 1 tCK 4. AUTO REFRESH and LOAD MODE REGISTER commands may only be issued when all banks are idle. 5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only. 6. All states and sequences not shown are illegal or reserved. 7. READs or WRITEs listed in the Command/Action column include READs or WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled. 8. Requires appropriate DM masking. 9. A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be used to end the READ burst prior to asserting a WRITE command. ABSOLUTE MAXIMUM RATINGS* VDD Supply Voltage Relative to Vss ..............................-1V to +3.6V VDDQ Supply Voltage Relative to VSS ............................-1V to +3.6V VREF and Inputs Voltage Relative to VSS ........................-1V to +3.6V I/O Pins Voltage Relative to VSS ...................... -0.5V to VDDQ +0.5V Operating Temperature, TA (ambient, Industrial) ....................................................-40C to +85C Operating Temperature, TA (ambient, Military) .....................................................-55C to +125C Storage Temperature (plastic) .................................-55C to +150C Power Dissipation...........................................................................1W Short Circuit Output Current .....................................................50mA *Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 36 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 9: DC ELECTRICAL CHARACTERISTICS AND OPERATION CONDITIONS (-55C < TA < +125C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) 1-5, 14, 16 PARAMETER Supply Voltage I/O Supply Voltage I/O Reference Voltage I/O Termination Voltage (system) Input High (Logic 1) Voltage Input Low (Logic 0) Voltage INPUT LEAKAGE CURRENT Any input 0V < VIN < VDD, VREF PIN 0V < VIN < 1.35V (All other pins not under test - 0V) OUTPUT LEAKAGE CURRENT (DQs are disabled; 0V < VOUT < VDDQ) OUTPUT LEVELS: Full drive option High Current (V OUT = VDDQ - 0.373V, min. VREF, min. VTT Low Current (V OUT = 0.373V, max. VREF, max. VTT) OUTPUT LEVELS: Reduced drive option High Current (V OUT = VDDQ - 0.763V, min. VREF, min. VTT Low Current (V OUT = 0.763V, max. VREF, max. VTT) II -2 2 A SYM VDD VDDQ VREF VTT VIH(DC) VIL(DC) MIN 2.3 2.3 MAX 2.7 2.7 UNITS V V V V V V NOTES 36, 41 36, 41, 44 6, 44 7, 44 28 28 0.49 x VDDQ 0.51 x VDDQ VREF - 0.04 VREF + 0.15 -0.3 VREF + 0.04 VDD + 0.3 VREF - 0.15 IOZ IOH IOL IOHR IOLR -5 -16.8 16.8 -9 9 5 --------- A mA 37, 39 mA mA 38, 39 mA TABLE 10: AC INPUT OPERATING CONDITIONS (-55C < TA < +125C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) 1-5, 14, 16 PARAMETER Input High (Logic 1) Voltage Input Low (Logic 0) Voltage I/O Reference Voltage SYM VIH(AC) VIL(AC) MIN VREF + 0.310 --MAX --VREF - 0.310 UNITS V V V NOTES 14, 28, 40 14, 28, 40 6 VREF(AC) 0.49 x VDDQ 0.51 x VDDQ AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 37 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 30: INPUT VOLTAGE WAVEFORM AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 38 Austin Semiconductor, Inc. TABLE 11: CLOCK INPUT OPERATING CONDITIONS COTS COTS PEM SDRAM AS4DDR32M16 (-55C < TA < +125C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) 1-5, 15, 16, 30 PARAMETER Clock Input Mid-Point Voltage; CK and CK# Clock Input Voltage Level; CK and CK# Clock Input Differential Voltage; CK and CK# Clock Input Differential Voltage; CK and CK# Clock Input Corssing Point Voltage; CK and CK# SYM VMP(DC) VIN(DC) VID(DC) VID(AC) VIX(AC) MIN 1.15 -0.3 0.36 0.7 MAX 1.35 VDDQ + 0.3 VDDQ + 0.6 VDDQ + 0.6 UNITS V V V V V NOTES 6, 9 6 6, 8 8 9 0.5 x VDDQ - 0.2 0.5 x VDDQ + 0.2 FIGURE 31: SSTL_2 CLOCK INPUT NOTES: 1. 2. 3. 4. 5. 6. 7. This provides a minimum of 1.15V to a maximum of 1.35V, and is always half of VDDQ. CK and CK# must cross in this region. CK and CK# must meet at least VID(DC) min when static and is centered around VMP(DC) CK and CK# must have a minimum 700mv peak to peak swing. CK or CK# may not be more positive than VDDQ+ 0.3V or more negative than Vss - 0.3V. For AC operation, all DC clock requirements must also be satisfied. Numbers in diagram reflect nominal values. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 39 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 12: CAPACITANCE13 PARAMETER Delta Input/Output Capacitance: DQ0-DQ7, LDQS, LDM Delta Input/Output Capacitance: DQ8-DQ15, UDQS, UDM Delta Input Capacitance: Command and Address Delta Input Capacitance: CK, CK# Input/Output Capacitance: DQ, LDQS, UDQS, LDM, UDM Input Capacitance: Command and Address Input Capacitance: CK, CK# Input Capacitance: CKE SYM DCIOL DCIOU DCI1 DCI2 CIO CI1 CI2 CI3 MIN --------4.0 2.0 2.0 2.0 MAX 0.50 0.50 0.50 0.25 5.0 3.0 3.0 3.0 UNITS pF pF pF pF pF pF pF pF NOTES 24 24 29 29 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 40 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 13: IDD SPECIFICATIONS AND CONDITIONS1-5, 10, 12, 14, 47 PARAMETER OPERATING CURRENT: One Bank; Active-Precharge; tRC = tRC(MIN); tCK = tCK(MIN); DQ, DM and DQS inputs changing once per clock cycle; Address and control inputs changing once every two clock cycles. OPERATING CURRENT: One Bank; Active-Read-Precharge; Burst = 4; tRC = tRC(MIN); tCK = tCK(MIN); IOUT = 0mA; Address and control inputs changing once per clock cycle. PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; Power-down mode; tCK = tCK(MIN); CKE = (LOW) IDLE STANDBY CURRENT: CS# - HIGH; All banks are idle; tCK = tCK(MIN); CKE = HIGH; Address and other control inputs changing once per clock cycle. VIN = VREF for DQ, DQS, and DM ACTIVE POWER-DOWN STANDBY CURRENT: One bank active; Power-down mode; tCK = tCK(MIN); CKE = LOW IDD3P 35 30 28 mA 23, 32, 50 SYM -6 MAX -75 -8 UNITS NOTES IDD0 130 115 110 mA 22, 48 IDD1 160 145 140 mA 22, 48 IDD2P 5 5 5 mA 23, 32, 50 IDD2F 45 40 38 mA 51 ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH; One bank active; tRC = tRAS(MAX); tCK = tCK(MIN); DQ, DM and DQS IDD3N inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle. OPERATING CURRENT: Burst = 2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock IDD4R cycle; tCK = tCK(MIN); IOUT = 0mA OPERATING CURRENT: Burst = 2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock IDD4W cycle; tCK = tCK(MIN); DQ, DM, and DQS inputs changing twice per clock cycle. AUTO REFRESH BURST CURRENT: SELF REFRESH CURRENT: CKE < 0.2V OPERATING CURRENT: Four bank interleaving READs (Burst = 4) with auto precharge, tRC = minimum tRC allowed; tCK = tCK(MIN); Address and control inputs change only during Active READ or WRITE commands. tRC = tRFC(MIN) tRFC = 7.8us IDD5 IDD5A IDD6 50 45 40 mA 22 165 145 140 mA 22, 48 195 135 128 mA 22 290 10 5 280 10 5 275 10 5 mA mA mA 50 27, 50 11 IDD7 405 350 325 mA 22, 49 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 41 Austin Semiconductor, Inc. TABLE 14: IDD TEST CYCLE TIMES (Values reflect number of clock cycles for each test.) IDD TEST SPEED GRADE -6 -75 -8 -6 -75 -8 -6 -75 -8 -6 -75 -8 -6 -75 -8 -6 -75 -8 -6 -75 -8 CLOCK CYCLE TIME 6ns 7.5ns 8ns 6ns 7.5ns 8ns 6ns 7.5ns 8ns 6ns 7.5ns 8ns 6ns 7.5ns 8ns 6ns 7.5ns 8ns 6ns 7.5ns 8ns COTS COTS PEM SDRAM AS4DDR32M16 tRRD N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 2/4 2/4 tRCD N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 3 3 tRAS 7 6 7 6 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A tRP 3 3 3 3 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 3 3 tRC 10 9 10 9 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 10 10 tRFC N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 12 10 12 10 N/A N/A N/A tREFI N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 12 10 1288 1029 N/A N/A N/A CL N/A N/A N/A 2.5 2.5 2.5 2.5 N/A N/A N/A N/A N/A N/A N/A N/A N/A 2.5 2.5 IDD0 IDD1 IDD4R IDD4W IDD5 IDD5A IDD7 AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 42 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 15: ELECTRICAL CHARACTERISTICS & RECOMMENDED AC OPERATING CONDITIONS (-55C < TA < +125C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) 1-5, 14-17, 33 -6 PARAMETER Access window of DQs from CK/CK# CK high-level width CK low-level width Clock cycle time CL = 2.5 CL = 2 DQ and DM input hold time relative to DQS DQ and DM input setup time relative to DQS DQ and DM input pulse width (for each input) Access window of DQS from CK/CK# DQS input high pulse width DQS input low pulse width DQS-DQ skew, DQS to last DQ valid, per group, per access Write command to first DQS latching transition DQS falling edge to CK rising - setup time DQS falling edge from CK rising - hold time Half clock period Data-out high-impedance window from CK/CK# Data-out low-impedance window from CK/CK# Address and control input hold time (fast slew rate) Address and control input setup time (fast slew rate) Address and control input hold time (slow slew rate) Address and control input setup time (slow slew rate) Address and control input pulse width (for each input) LOAD MODE REGISTER command cycle time SYM tAC tCH tCL tCK(2.5) tCK(2) tDH tDS tDIPW tDQSCK tDQSH tDQSL tDQSQ tDQSS tDSS tDSH tHP tHZ tLZ tIHF tISF tIHs tISs tIPW tMRD -0.7 0.75 0.75 0.8 0.8 2.2 12 0.75 0.2 0.2 tCH, tCL +0.7 -0.75 0.90 0.90 1 1 2.2 15 MIN -0.70 0.45 0.45 6 7.5 0.45 0.45 1.75 -0.6 0.35 0.35 0.45 1.25 0.75 0.2 0.2 tCH, tCL +0.75 -0.8 1.1 1.1 1.2 1.2 2.2 16 tCH, tCL +0.8 +0.6 MAX +0.70 0.55 0.55 13 13 MIN -0.75 0.45 0.45 7.5 10 0.5 0.5 1.75 -0.75 0.35 0.35 0.5 1.25 0.75 +0.75 -0.8 -75 MAX +0.75 0.55 0.55 13 13 MIN -0.8 0.45 0.45 8 10 -8 MAX +0.8 0.55 0.55 13 13 0.6 0.6 2.00 +0.8 0.35 0.35 0.6 1.25 0.2 0.2 UNITS ns tCK tCK ns ns ns ns ns ns tCK tCK ns tCK tCK tCK ns ns ns ns ns ns ns ns ns 14 14 34 18, 42 18, 43 25, 26 30 30 45, 52 45, 52 26, 31 26, 31 31 NOTES (CONTINUED) AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 43 Austin Semiconductor, Inc. CONDITIONS (CONTINUED) 1-5, 14-17, 33 -6 PARAMETER DQ-DQS hold, DQS to first DQ to go non-valid, per access Data Hold Skew Factor ACTIVE to PRECHARGE command ACTIVE to READ with Auto precharge command ACTIVE to ACTIVE/AUTO REFRESH command period AUTO REFRESH command period ACTIVE to READ or WRITE delay PRECHARGE command period DQS read preamble DQS read postamble ACTIVE bank a to Active bank b command DQS write preamble DQS write preamble setup time DQS write postamble Write recovery time Internal WRITE to READ command delay Data valid ouput window (DVW) REFRESH to REFRESH command interval Average periodic refresh interval Terminating voltage delay to VDD Exit SELF REFRESH to non-READ command Exit SELF REFRESH to READ command SYM tQH tQHS tRAS tRAP tRC tRFC tRCD tRP tRPRE tRPST tRRD tWPRE tWPRES tWPST tWR tWTR N/A tREFC tREFI tVTD tXSNR tXSRD 0 75 200 42 15 60 72 15 15 0.9 0.4 12 0.25 0 0.4 15 1 tQH - tDQSQ 70.3 7.8 0 75 200 0.6 1.1 0.6 MIN tHP - tQHS 0.55 70,000 40 20 65 75 20 20 0.9 0.4 15 0.25 0 0.4 15 1 tQH - tDQSQ 70.3 7.8 0.6 1.1 0.6 MAX MIN tHP - tQHS 0.75 120,000 -75 MAX COTS COTS PEM SDRAM AS4DDR32M16 TABLE 15: ELECTRICAL CHARACTERISTICS & RECOMMENDED AC OPERATING -8 MIN tHP - tQHS 1.0 40 20 70 80 20 20 0.9 0.4 16 0.25 0 0.4 18 1 tQH - tDQSQ 70.3 7.8 0 80 200 0.6 1.1 0.6 120,000 MAX UNITS ns ns ns ns ns ns ns ns tCK tCK ns tCK ns tCK ns tCK ns s s ns ns tCK 25 23 23 20, 21 19 42 50 35 NOTES 25, 26 TABLE 16: INPUT SLEW RATE DERATING VALUES FOR ADDRESSES AND COMMANDS FOR -75 OPTION (-55C < TA < +125C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) 14 SLEW RATE 0.500V/ns 0.400V/ns 0.300V/ns tIS 1.00 1.05 1.15 tIH 1 1 1 UNITS ns ns ns TABLE 17: INPUT SLEW RATE DERATING VALUES FOR DQ, DQS, & DM FOR -75 OPTION (-55C < TA < +125C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) 31 SLEW RATE 0.500V/ns 0.400V/ns 0.300V/ns AS4DDR32M16 Rev. 1.5 06/06 tDS 0.50 0.55 0.60 tDH 0.50 0.55 0.60 UNITS ns ns ns Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 44 Austin Semiconductor, Inc. NOTES: 1. All voltages referenced to VSS. 2. Tests for AC timing, IDD, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. 3. Outputs (except for IDD measurements) measured with equivalent load: COTS COTS PEM SDRAM AS4DDR32M16 4. AC timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test environment, but input timing is still referenced to VREF (or to the crossing point for CK/CK#), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions. The minimum slew rate for the input signals used to test the device is 1V/ns in the range between VIL(AC) and VIH(AC). 5. The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result of the signal crossing the AC input level, and will remain in that state as long as the signal does not ring back above [below] the DC input LOW [HIGH] level). 6. VREF is expected to equal VDDQ/2 of the transmitting device and to track variations in the DC level of the same. Peak-to-peak noise (non-common mode) on VREF may not exceed 2 percent of the DC value. Thus, from VDDQ/2, VREF is allowed 25mV for DC error and an additional 25mV for AC noise. This measurement is to be taken at the nearest VREF by-pass capacitor. 7. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF and must track variations in the DC level of VREF. 8. VID is the magnitude of the difference between the input level on CK and the input level on CK#. 9. The value of VIX and VMP are expected to equal VDDQ/2 of the transmitting device and must track variations in the DC level of the same. 10. IDD is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle times at CL=2.5 with the outputs open. 11. Enables on-chip refresh and address counters. 12. IDD specifications are tested after the device is properly initialized, and is averaged at the defined cycle rate. 13. This parameter is sampled. VDD=+2.5V0.2V, VDDQ=+2.5V0.2V, VREF=VSS, f=100MHz, TA=25C VOUT(DC)=VDDQ/2, VOUT (peak to peak)=0.2V. DM input is grouped with I/O pins, reflecting the fact that they are matched in loading. 14. For slew rates less than 1V/ns and and greater than or equal to 0.5V/ ns. If the slew rate is less than 0.5V/ns, timing must be derated: tIS has an additional 50ps per each 100mV/ns reduction in slew rate from the 500mV/ ns. tIH has 0ps added, that is, it remains constant. If the slew rate exceeds 4.5V/ns, functionality is uncertain. 15. The CK/CK# input reference level (for timing referenced to CK/ CK#) is the point at which CK and CK# cross; the input reference level for signals other than CK/CK# is VREF. 16. Inputs are not recognized as valid until VREF stabilizes. Once initialized, including self refresh mode, VREF must be powered within specified range. Exception: during the period before VREF stabilizes, CKE 0.3 x VDDQ is recognized as LOW. 17. The output timing reference level, as measured at the timing reference point indicated in Note 3, is VTT. AS4DDR32M16 Rev. 1.5 06/06 18. tHZ and tLZ transitions occur in the same access time windows as data valid transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving (HZ) or begins driving (LZ). 19. The intent of the Don't Care state after completion of the postamble is the DQS-driven signal should either be high, low, or high-Z and that any signal transition within the input switching region must follow valid input requirements. That is, if DQS transitions high (above VIHDC(MIN) then it must not transition low (below VIHDC) prior to tDQSH(MIN). 20. This is not a device limit. The device will operate with a negative value, but system performance could be degraded due to bus turnaround. 21. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command. The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were previously in progress on the bus. If a previous WRITE was in progress, DQS could be HIGH during this time, depending on tDQSS. 22. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets the minimum absolute value for the respective parameter. tRAS (MAX) for IDD measurements is the largest multiple of tCK that meets the maximum absolute value for tRAS. 23. The refresh period is 64ms. This equates to an average refresh rate of 7.8125s. However, an AUTO REFRESH command must be asserted at least once every 70.3s; burst refreshing or posting by the DRAM controller greater than eight refresh cycles is not allowed. 24. The I/O capacitance per DQS and DQ byte/group will not differ by more than this maximum amount for any given device. 25. The data valid window is derived by achieving other specifications tHP (tCK/2), tDQSQ, and tQH (tQH = tHP - tQHS). The data valid window derates in direct proportion to the clock duty cycle and a practical data valid window can be derived. The clock is allowed a maximum duty cycle variation of 45/55, because functionality is uncertain when operating beyond a 45/55 ratio. The data valid window derating curves are provided in Figure 32 for duty cycles ranging between 50/50 and 45/55. 26. Referenced to each output group: x4 = DQS with DQ0-DQ3; x8 = DQS with DQ0-DQ7; x16 = LDQS with DQ0-DQ7; and UDQS with DQ8DQ15. 27. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during standby). 28. To maintain a valid level, the transitioning edge of the input must: a. Sustain a constant slew rate from the current AC level through to the target AC level, VIL(AC) or VIH(AC). b. Reach at least the target AC level. c. After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC). 29. The Input capacitance per pin group will not differ by more than this maximum amount for any given device. 30. CK and CK# input slew rate must be > 1V/ns (> 2V/ns if measured differentially). 31. DQ and DM input slew rates must not deviate from DQS by more than 10 percent. If the DQ/DM/DQS slew rate is less than 0.5V/ns, timing must be derated: 50ps must be added to tDS and tDH for each 100mv/ns reduction in slew rate. For -6 speed grades, slew rate must be > 0.5V/ns. If slew rate exceeds 4V/ns, functionality is uncertain. 32. VDD must not vary more than 4 percent if CKE is not active while any bank is active. 33. The clock is allowed up to 150ps of jitter. Each timing parameter is allowed to vary by the same amount. 34. tHP (MIN) is the lesser of tCL minimum and tCH minimum actually applied to the device CK and CK# inputs, collectively during bank active. (continued) Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 45 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 32: DERATING DATA VALID WINDOW (tQH - tDQSQ) NOTES (continued): 35. READs and WRITEs with auto precharge are not allowed to be issued until tRAS (MIN) can be satisfied prior to the internal precharge command being issued. 36. Any positive glitch must be less than 1/3 of the clock cycle and not more than +400mV or 2.9V, whichever is less. Any negative glitch must be less than 1/3 of the clock cycle and not exceed either -300mV or 2.2V, whichever is more positive. 37. Normal Output Drive Curves: a. The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure 33 b. The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure 33. c. The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure 34. d. The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure 34. e. The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between 0.71 and 1.4, for device drain-to-source voltages from 0.1V to 1.0V, and at the same voltage and temperature. f ) The full variation in the ratio of the nominal pullup to pull-down current should be unity 10 percent, for device drain-to-source voltages from 0.1V to 1.0V. (continued) FIGURE 33: FULL DRIVE PULLDOWN CHARACTERISTICS FIGURE 34: FULL DRIVE PULL-UP CHARACTERISTICS AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 46 Austin Semiconductor, Inc. NOTES (continued): 38. Reduced Output Drive Curves: a. The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure 35. b. The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure 35. c. The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure 36. d. The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure 36. e. The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between 0.71 and 1.4 for device drainto-source voltages from 0.1V to 1.0V, and at the same voltage and temperature. f. The full variation in the ratio of the nominal pull-up to pull-down current should be unity 10 percent, for device drain-to-source voltages from 0.1V to 1.0V. 39. The voltage levels used are derived from a minimum VDD level and the referenced test load. In practice, the voltage levels obtained from a properly terminated bus will provide significantly different voltage values. 40. VIH overshoot: VIH (MAX) = VDDQ + 1.5V for a pulse width < 3ns and the pulse width can not be greater than 1/3 of the cycle rate. VIL undershoot: VIL (MIN) = -1.5V for a pulse width < 3ns and the pulse width can not be greater than 1/3 of the cycle rate. 41. VDD and VDDQ must track each other. 42. tHZ (MAX) will prevail over tDQSCK (MAX) + tRPST (MAX) condition. tLZ (MIN) will prevail over tDQSCK (MIN) + tRPRE (MAX) condition. 43. tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). 44. During initialization, VDDQ, VTT, and VREF must be equal to or less than VDD + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even VDD/VDDQ are 0V, providind a minimum of 42 of series resistance is used between the VTT supply and the input pin. 45. The current Austin Semiconductor part operates below the slowest JEDEC operating frequency of 83 MHz. As such, future die may not reflect this option. 46. When an input signal is HIGH or LOW, it is defined as a steady state logic HIGH or LOW. 47. Random addressing changing 50 percent of data changing at every transfer. 48. Random addressing changing 100 percent of data changing at every transfer. 49. CKE must be active (HIGH) during the entire time a refresh command is executed. That is, from the time the AUTO REFRESH command is registered, CKE must be active at each rising lock edge, until rRFC has been satisfied. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 35: REDUCED DRIVE PULLDOWN CHARACTERISTICS FIGURE 36: REDUCED DRIVE PULLUP CHARACTERISTICS 50. IDD2N specifies the DQ, DQS, and DM to be driven to a valid high or low logic level. IDD2Q is similar to IDD2F except IDD2Q specifies the address and control inputs to remail stable. Although IDD2F, IDD2N and IDD2Q are similar, IDD2F is "worst case". 51. Whenever the operating frequency is altered, not including jitter, the DLL is required to the reset followed by 200 clock cycles befoe any READ command. 52. This is the DC voltage supplied at the DRAM and is inclusive of all noise up to 20MHz. Any noise above 20MHz at the DRAM grenerated from any source other than that of the DRAM itself may not exceed the DC voltage range of 2.6V 100mV. 53. The -6/-6T speed grades will operate with tRAS (MIN) = 40ns and tRAS (MAX) = 120,000ns at any slower frequency. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 47 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 18: NORMAL OUTPUT DRIVE CHARACTERISTICS PULL-DOWN CURRENT (mA PULL-UP CURRENT (mA VOLTAGE NOMINAL NOMINAL NOMINAL NOMINAL (V) MINIMUM MAXIMUM MINIMUM MAXIMUM HIGH LOW HIGH LOW 0.1 6.0 6.8 4.6 9.6 -6.1 -7.6 -4.6 -10.0 0.2 12.2 13.5 9.2 18.2 -12.2 -14.5 -9.2 -20.0 0.3 18.1 20.1 13.8 26.0 -18.1 -21.2 -13.8 -29.8 0.4 24.1 26.6 18.4 33.9 -24.0 -27.7 -18.4 -38.8 0.5 29.8 33.0 23.0 41.8 -29.8 -34.1 -23.0 -46.8 0.6 34.6 39.1 27.7 49.4 -34.3 -40.5 -27.7 -54.4 0.7 39.4 44.2 32.2 56.8 -38.1 -46.9 -32.2 -61.8 0.8 43.7 49.8 36.8 63.2 -41.1 -53.1 -36.0 -69.5 0.9 47.5 55.2 39.6 69.9 -43.8 -59.4 -38.2 -77.3 1.0 51.3 60.3 42.6 76.3 -46.0 -65.5 -38.7 -85.2 1.1 54.1 65.2 44.8 82.5 -47.8 -71.6 -39.0 -93.0 1.2 56.2 69.9 46.2 88.3 -49.2 -77.6 -39.2 -100.6 1.3 57.9 74.2 47.1 93.8 -50.0 -83.6 -39.4 -108.1 1.4 59.3 78.4 47.4 99.1 -50.5 -89.7 -39.6 -115.5 1.5 60.1 82.3 47.7 103.8 -50.7 -95.5 -39.9 -123.0 1.6 60.5 85.9 48.0 108.4 -51.0 -101.3 -40.1 -130.4 1.7 61.0 89.1 48.4 112.1 -51.1 -107.1 -40.2 -136.7 1.8 61.5 92.2 48.9 115.9 -51.3 -112.4 -40.3 -144.2 1.9 62.0 95.3 49.1 119.6 -51.5 -118.7 -40.4 -150.5 49.4 2.0 62.5 97.2 123.3 -51.6 -124.0 -40.5 -156.9 2.1 62.8 99.1 49.6 126.5 -51.8 -129.3 -40.6 -163.2 2.2 63.3 100.9 49.8 129.5 -52.0 -134.6 -40.7 -169.6 2.3 63.8 101.9 49.9 132.4 -52.2 -139.9 -40.8 -176.0 2.4 64.1 102.8 50.0 135.0 -52.3 -145.2 -40.9 -181.3 2.5 64.6 103.8 50.2 137.3 -52.5 -150.5 -41.0 -187.6 2.6 64.8 104.6 50.4 139.2 -52.7 -155.3 -41.1 -192.9 2.7 65.0 105.4 50.5 140.8 -52.8 -160.1 -41.2 -198.2 NOTE: The above characteristics are specified under best, worse, and nominal process variation/conditions. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 48 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 TABLE 19: REDUCED OUTPUT DRIVE CHARACTERISTICS PULL-DOWN CURRENT (mA PULL-UP CURRENT (mA VOLTAGE NOMINAL NOMINAL NOMINAL NOMINAL (V) MINIMUM MAXIMUM MINIMUM MAXIMUM HIGH LOW HIGH LOW 0.1 3.4 3.8 2.6 5.0 -3.5 -4.3 -2.6 -5.0 0.2 6.9 7.6 5.2 9.9 -6.9 -7.8 -5.2 -9.9 0.3 10.3 11.4 7.8 14.6 -10.3 -12.0 -7.8 -14.6 0.4 13.6 15.1 10.4 19.2 -13.6 -15.7 -10.4 -19.2 0.5 16.9 18.7 13.0 23.6 -16.9 -19.3 -13.0 -23.6 0.6 19.9 22.1 15.7 28.0 -19.4 -22.9 -15.7 -28.0 0.7 22.3 25.0 18.2 32.2 -21.5 -26.5 -18.2 -32.2 0.8 24.7 28.2 20.8 38.8 -23.3 -30.1 -20.4 -35.8 0.9 26.9 31.3 22.4 39.5 -24.8 -33.6 -21.6 -39.2 1.0 29.0 34.1 24.1 43.2 -26.0 -37.1 -21.9 -43.2 1.1 30.6 36.9 25.4 46.7 -27.1 -40.3 -22.1 -46.7 1.2 31.8 39.5 26.2 50.0 -27.8 -43.1 -22.2 -50.0 1.3 32.8 42.0 26.6 53.1 -28.3 -45.8 -22.3 -53.1 1.4 33.5 44.4 26.8 56.1 -28.6 -48.4 -22.4 -56.1 1.5 34.0 46.6 27.0 58.7 -28.7 -50.7 -22.6 -58.7 1.6 34.3 48.6 27.2 61.4 -28.9 -52.9 -22.7 -61.4 1.7 34.5 50.5 27.4 63.5 -28.9 -55.0 -22.7 -63.5 1.8 34.8 52.2 27.7 65.6 -29.0 -56.8 -22.8 -65.6 1.9 35.1 53.9 27.8 67.7 -29.2 -58.7 -22.9 -67.7 28 2.0 35.4 55.0 69.8 -29.2 -60.0 -22.9 -69.8 2.1 35.6 56.1 28.1 71.6 -29.3 -61.2 -23.0 -70.6 2.2 35.8 57.1 28.2 73.3 -29.5 -62.4 -23.0 -73.3 2.3 36.1 57.7 28.3 74.9 -29.5 -63.1 -23.1 -74.9 2.4 36.6 58.2 28.3 76.4 -29.6 .63.8 -23.2 -76.4 2.5 36.5 58.7 28.4 77.7 -29.7 -64.4 -23.2 -77.7 2.6 36.7 59.2 28.5 78.8 -29.8 -65.1 -23.3 -78.8 2.7 36.8 59.6 28.6 79.7 -29.9 -65.8 -23.3 -79.7 NOTE: The above characteristics are specified under best, worse, and nominal process variation/conditions. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 49 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 37: DATA OUTPUT TIMING - tDQSQ, tQH, and DATA VALID WINDOW NOTES: 1. 2. 3. 4. 5. 6. 7. DQ transitioning after DQS transition define tDQSQ window. LDQS defines the lower byte and UDQS defines the upper byte. DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, or DQ7. tDQSQ is derived at each DQS clock edge and is not cumulative over time and begins with DQS transition and ends with the last valid DQ transition. tQH is derived from tHP: tQH = tHP - tQHS. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active. The data valid window is derived for each DQS transition and is tQH minus tDQSQ. DQ8, DQ9, DQ10, D11, DQ12, DQ13, DQ14, or DQ15. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. AS4DDR32M16 Rev. 1.5 06/06 50 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 38: DATA OUTPUT TIMING - tAC AND tDQSCK NOTES: 1. 2. 3. 4. 5. 6. 7. tDQSCK is the DQS output window relative to CK and is the "long term" component of DQS skew. DQ transitioning after DQS transition define tDQSQ window. All DQ must transition by tDQSQ after DQS transitions, regardless of tAC. tAC is the DQ output window relative to CK, and is the "long term" component of DQ skew. tLZ (MIN) and tAC (MIN) are the first valid signal transition. tHZ (MAX),and tAC (MAX) are the latest valid signal transition. READ command with CL = 2 issued at T0. FIGURE 39: DATA INPUT TIMING NOTES: 1. 2. 3. 4. tDSH (MIN) generally occurs during tDQSS (MIN). tDSS (MIN) generally occurs during tDQSS (MAX). WRITE command issued at T0. LDQS controls the lower byte and UDQS controls the upper byte. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. AS4DDR32M16 Rev. 1.5 06/06 51 Austin Semiconductor, Inc. INITIALIZATION COTS COTS PEM SDRAM AS4DDR32M16 To ensure device operation the DRAM must be initialized as described below: 1. Simultaneously apply power to VDD and VDDQ. 2. Apply VREF and then VTT power. 3. Assert and hold CKE at a LVCMOS logic low. 4. Provide stable CLOCK signals. 5. Wait at least 200s. 6. Bring CKE high and provide at least one NOP or DESELECT command. At this point the CKE input changes from a LVCMOS input to a SSTL2 input only and will remain a SSTL_2 input unless a power cycle occurs. 7. Perform a PRECHARGE ALL command. 8. Wait at least tRP time, during this time NOPs or DESELECT commands must be given. 9. Using the LMR command program the Extended Mode Register (E0 = 0 to enable the DLL and E1 = 0 for normal drive or E1 = 1 for reduced drive, E2 through En must be set to 0; where n = most significant bit). 10. Wait at least tMRD time, only NOPs or DESELECT commands are allowed. 11. Using the LMR command program the Mode Register to set operating parameters and to reset the DLL. Note at least 200 clock cycles are required between a DLL reset and any READ command. 12. Wait at least tMRD time, only NOPs or DESELECT commands are allowed. 13. Issue a PRECHARGE ALL command. 14. Wait at least tRP time, only NOPs or DESELECT commands are allowed. 15. Issue an AUTO REFRESH command (Note this may be moved prior to step 13). 16. Wait at least tRFC time, only NOPs or DESELECT commands are allowed. 17. Issue an AUTO REFRESH command (Note this may be moved prior to step 13). 18. Wait at least tRFC time, only NOPs or DESELECT commands are allowed. 19. Although not required by the Micron device, JEDEC requires a LMR command to clear the DLL bit (set M8 = 0). If a LMR command is issued the same operating parameters should be utilized as in step 11. 20. Wait at least tMRD time, only NOPs or DESELECT commands are allowed. 21. At this point the DRAM is ready for any valid command. Note 200 clock cycles with CKE high are required between step 11 (DLL RESET) and any READ command. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 52 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 40: Initialization Flow Diagram AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 53 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 41: INITIALIZE AND LOAD MODE REGISTERS NOTES: 1. VTT is not applied directly to the device; however, tVTD should be greater than or equal to zero to avoid device latch-up. VDDQ, VTT, and VREF, must be equal to or less than VDD + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even if VDD/VDDQ are 0V, provided a minimum of 42 ohms of series resistance is used between the VTT supply and the input pin. Once initialized, VREF must always be powered with in specified range. 2. Reset the DLL with A8 = H while programming the operating parameters. 3. tMRD is required before any command can be applied, and 200 cycles of CK are required before a READ command can be issued. 4. The two AUTO REFRESH commands at Td0 and Te0 may be applied prior to the LOAD MODE REGISTER (LMR) command at Ta0. 5. Although not required by the Micron device, JEDEC specifies issuing another LMR command (A8 = L) prior to activating any bank. If another LMR command is issued, the same operating parameters, previously issued, must be used. 6. PRE = PRECHARGE command, LMR = LOAD MODE REGISTER command, AR = AUTO REFRESH command, ACT = ACTIVE command, RA = Row Address, BA = Bank Address. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 54 Austin Semiconductor, Inc. FIGURE 42: POWER-DOWN MODE COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. Once initialized, VREF must always be powered with in specified range. 2. If this command is a PRECHARGE (or if the device is already in the idle state), then the power-down mode shown is precharge power-down. If this command is an ACTIVE (or if at least one row is already active), then the power-down mode shown is active power-down. 3. No column accesses are allowed to be in progress at the time power-down is entered. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 55 Austin Semiconductor, Inc. FIGURE 43: AUTO REFRESH MODE COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. PRE = PRECHARGE, ACT = ACTIVE, AR = AUTO REFRESH, RA = Row Address, BA = Bank Address. 2. NOP commands are shown for ease of illustration; other valid commands may be possible at these times. CKE must be active during clock positive transitions. 3. NOP or COMMAND INHIBIT are the only commands allowed until after tRFC time, CKE must be active during clock positive transitions. 4. "Don't Care" if A10 is HIGH at this point; A10 must be HIGH if more than one bank is active (i.e., must precharge all active banks). 5. DM, DQ, and DQS signals are all "Don't Care"/High-Z for operations shown. 6. The second AUTO REFRESH is not required and is only shown as an example of two back-to-back AUTO REFRESH commands. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 56 Austin Semiconductor, Inc. FIGURE 44: SELF REFRESH MODE COTS COTS PEM SDRAM AS4DDR32M16 NOTES: 1. Clock must be stable until after the self refresh command has been registered. A change in clock frequency is allowed before Ta0, provided it is within the specified tCK limits. Regardless, the clock must be stable before exiting self refresh mode. That is, the clock must be cycling within specifications by Ta0. 2. NOPs are interchangeable with DESELECT commands, AR = AUTO REFRESH command. 3. Auto Refresh is not required at this point, but is highly recommended. 4. Device must be in the all banks idle state prior to entering self refresh mode. 5. tXSNR is required before any non-READ command can be applied. That is only NOP or DESELECT commands are allowed until Tb1. 6. tXSRD (200 cycles of a valid CK and CKE = high) is required before any READ command can be applied. 7. As a general rule, any time Self Refresh Mode is exited, the DRAM may not re-enter the Self Refresh Mode until all rows have been refreshed via the Auto Refresh command at the distributed refresh rate, tREFI, or faster. However, the following exception is allowed. Self Refresh Mode may be re-entered anytime after exiting, if the following conditions are all met: a. The DRAM had been in the Self Refresh Mode for a minimum of 200ms prior to exiting. b. tXSNR and tXSRD are not violated. c. At least two Auto Refresh commands are performed during each tREFI interval while the DRAM remains out of Self Refresh mode. 8. If the clock frequency is changed during self refresh mode, a DLL reset is required upon exit. 9. Once initialized, Vref must always be powered with in specified range. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 57 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 45: BANK READ - WITHOUT AUTO PRECHARGE NOTES: 1. 2. 3. 4. 5. 6. 7. 8. DOn = data-out from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Disable auto precharge. "Don't Care" if A10 is HIGH at T5. PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. The PRECHARGE command can only be applied at T5 if tRAS minimum is met. Refer to Figure 37 and Figure 38 for detailed DQS and DQ timing. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. AS4DDR32M16 Rev. 1.5 06/06 58 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 46: BANK READ - WITH AUTO PRECHARGE NOTES: 1. DOn = data-out from column n; subsequent elements are provided in the programmed order. 2. Burst length = 4 in the case shown. 3. Enable auto precharge. 4. ACT = ACTIVE, RA = Row Address, BA = Bank Address. 5. NOP commands are shown for ease of illustration; other commands may be valid at these times. 6. The READ command can only be applied at T3 if tRAP is satisfied at T3. 7. tRP starts only after tRAS has been satisfied. 8. Refer to Figure 37 and Figure 38 for detailed DQS and DQ timing. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 59 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 47: BANK WRITE - WITHOUT AUTO PRECHARGE NOTES: 1. 2. 3. 4. 5. 6. 7. DIn = data-in. from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Disable auto precharge. "Don't Care" if A10 is HIGH at T8. PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. See Figure 39, "Data Input Timing" for detailed DQ timing. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 60 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 48: BANK WRITE - WITH AUTO PRECHARGE NOTES: 1. DIn = data-out from column n; subsequent elements are provided in the programmed order. 2. Burst length = 4 in the case shown. 3. Enable auto precharge. 4. ACT = ACTIVE, RA = Row Address, BA = Bank Address. 5. NOP commands are shown for ease of illustration; other commands may be valid at these times. 6. See Figure 39, "Data Input Timing" for detailed DQ timing. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 61 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 49: WRITE - DM OPERATION NOTES: 1. 2. 3. 4. 5. 6. 7. DIn = data-in from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Disable auto precharge. "Don't Care" if A10 is HIGH at T8. PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. See Figure 39, "Data Input Timing" for detailed DQ timing. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 62 Austin Semiconductor, Inc. COTS COTS PEM SDRAM AS4DDR32M16 FIGURE 50: 66-PIN PLASTIC TSOP (400 MIL) ASI DESIGNATOR DG NOTES: 1. All dimensions in millimeters 2. Package width and length do not include mold protrusion; allowable mold protrusion is 0.25mm per side. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 63 Austin Semiconductor, Inc. ORDER CHART COTS COTS PEM SDRAM AS4DDR32M16 EXAMPLE: AS4DDR32M16DG-75/IT Device Number AS4DDR32M16 AS4DDR32M16 AS4DDR32M16 Package Type DG DG DG Speed ns -61 -75 -8 Process /IT /* /* 2 *AVAILABLE PROCESSES IT = Industrial Temperature Range ET = Enhanced Temperature Range XT = Extended Temperature Range -40oC to +85oC -40oC to +105oC -55oC to +125oC NOTE: 1. This is a future offering. Contact your local sales representative for more information. 2. The -6 option is available at XT only. AS4DDR32M16 Rev. 1.5 06/06 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 64 |
Price & Availability of AS4DDR32M16
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |